Knowledgebase
(6)Vigor120
(8)Vigor130
(7)Vigor2120
(1)Vigor2132
(32)Vigor2760
(17)Vigor2830
(2)Vigor2832
(65)Vigor2860
(1)Vigor2862
(6)Vigor2912
(43)Vigor2925
(6)Vigor2952
(14)Vigor2960
(8)Vigor300B
(6)Vigor3220
(33)Vigor3300V
(31)Vigor3900
(5)VigorAP 800
(3)VigorAP810
(7)VigorAP 900
(3)VigorAP 910C
(3)VigorBX 2000
(20)IPPBX
(2)VigorSwitch
(1)Security
(2)Downloads
(7)Firmware
(51)Getting Started
(95)Internet Access (WAN)
(43)NBN
(32)3G/4G
(33)Local Area Network (LAN)
(2)Smart Monitor
(25)Network Address Translation (NAT)
(78)Firewall / Security
(21)Bandwidth Management (QoS)
(36)Applications
(7)VigorACS SI
(73)VPN and Remote Access
(86)Voice over Internet (VoIP)
(5)USB Application
(68)Wireless LAN
(8)Virtual Local Area Network (VLAN)
(9)Printer Server
(55)System Maintenance / Troubleshooting
(6)Diagnostics
(69)Videos
(12)Webinars
(3)PenPower Products
* Connect a computer's serial port to the Vigor 3300 Console port
using the supplied cable. this).
* On the computer, run a terminal emulator, such as the Windows
Hyperterminal. Configure the serial port as:
* In Hyperterminal, choose the "CaptureT...
The Vigor 3300 models use the same list of profiles for LAN-to-LAN and host-to-LAN (teleworker) VPNs. There are however a subtle difference depending on whether the other endpoint has a static or dynamic IP address: Where the other endpoint has a static I...
Because Vigor 3300 / 3300V user interface is very different from other Vigor models, we have created a top-level FAQ category for them. Fo now, click here. In future you will find all Vigor 3300 FAQs under " [10] Vigor 3300 / 3300V" on the...
* Connect a computer's serial port to the Vigor 3300 Console port
using the supplied cable. this).
* On the computer, run a terminal emulator, such as the Windows
Hyperterminal. Configure the serial port as:
* In Hyperterminal, choose the "CaptureT...
The Vigor 3300 (not 3300V) model have the DMZ and WAN ports mis-labelled. The front of the unit shows a block of 4 LAN ports (P1-P4) and a block of 4 WAN ports, labelled "DMZ", "WAN1", "WAN2" and "ISDN". However...
There is a socket on the Vigor 3300's front panel labelled "DMZ". This is actually the "WAN1 port" (see here for details). The current Vigor 3300 firmware can use any of the 3 WAN ports for DMZ. This is configured in the Advanced...
The "Local ID" field is used for IPSec Aggressive mode which is not supported on 3300 series; so the Vigor 3300V don't have "Local ID" field. There are two cases. Â Aggressive mode is used in IPSec IKE phase 1. Currently, 3300 doesn'...
The Draytek Manufacturer has a comprehensive set of Application Notes regarding the 3300/3300V on their website. Please refer to the WAN settings documentation here: http://www.draytek.com/user/SupportAppnotesDetail.php?ID=62
The Draytek Manufacturer has a comprehensive set of Application Notes regarding the 3300/3300V on their website. Please refer to the VPN settings documentation here: http://www.draytek.com/user/SupportAppnotes.php?Id=83
The Draytek Manufacturer has a comprehensive set of Application Notes regarding the 3300/3300V on their website. Please refer to the Firmware Upgrade Notes (Chapter 17) here: http://www.draytek.com/user/SupportAppnotesDetail.php?ID=64
We are aware that TelecomNZ doesn't support PPPoE (which is common in Australia), and that NZ customers must use PPPoA. This requires that the modem is configured to do the PPPoA login. It is preferable if the modem can be configured to "Bridge&quo...
Not directly, because the Vigor 3300 does not provide all the functions of a modern PBX. However see this Draytek Vigor 3300V Application Note on using Vigor 3300V with Asterisk Open-source PBX.
The Draytek Manufacturer has a comprehensive set of Application Notes regarding the 3300/3300V on their website. Please refer to the VOIP settings documentation here: http://www.draytek.com/user/SupportAppnotes.php?Id=83
OK, so what you're trying to achieve is: (a) An incoming PSTN call is converted by the 3300V to a VoIP data stream and sent via Ethernet to the Asterisk server where it is handled as an incoming call. (b) When users dial a PSTN number the Asterisk PBX sen...
VIGOR3300 CONFIGURATION
STEP1: Go To "VPN>>PPTP&L2TP>>General Setup>>PPTP General Setup" page.
Enable profile and select Authentication method and Encryption
STEP2: Go to "VPN>> Group Table" Setup
Enter IP subnet to use for the VPN connection. Here...
For source and destination IP to specify ANY use 0.0.0.0
Under service type specify none to indicate ANY
DiffServ Codepoint leave it at "none" unless the server supports this.
Assume we want 60% bandwidth allocated to VoIP.
Assume the VoIP system is at ...
This article describes how the high availability works with the
vigor3300 routers:
After enabling HIGH AVAILABILITY on both 3300 and setup the LAN IP
and virtual IP addresses, the Slave unit will download and sync the
settings from the Master unit aut...
This function is available from firmware version 2.6.2 and above and
is only available in the Command Line Interface of the router.
Telnet to the router and run the "SWITCHPORT" command. This is
available in the network configuration option.
The synta...
The Vigor3300 router does not have a factory reset button on the
front panel similar to the Vigor3300V router. Therefore we will need
to use the console port to gain access to the router and perform the
factory reset.
Below are the steps required to...
Vigor3300 running firmware version 2.6.3 (EN) supports scheduled
rebooting of the router. Telnet system command to use is
"_autoreboot"_
Command syntax is:
DRAYTEK/SYSTEM> AUTOREBOOT ?
FULL NAME:
AUTO REBOOT FUNCTION
DESCRIPTION:
SYNTAX:
...
The Vigor3300 supports VPN pass through.
The VPN server will need to use ESP for IPSEC VPN security method.
The NAT mechanism in the Vigor3300 supports NAT-T when ESP is used.
The AH security method does not support NAT-T
Before you start to configure VOIP on your Vigor3300V router ensure
that you have connected the Analogue Phones to the router and the
router is connected to the Internet.
Your chosen VoIP Provider will supply you with the details required to
configure y...
Since VoIP devices use various RTP ports, it is recommended to set the
QoS rule by IP.
Assume the VoIP device behind Vigor3300 is with IP 192.168.33.100.
Please follow the steps below to configure QoS rule.
STEP 1
Set the real bandwidth of WAN1.
...
You can use the console port to re-enable access to the router.
Connect your Computer serial port to the Vigor3300 console port.
Console port settings: baud rate 57600, 8 bits, no parity,1 stop bit
once you log into the router issue the following comma...
SCENARIO
Currently have network 192.168.16.0 configured on LAN port 1.
Need to set up a second subnet 10.0.1.0 on LAN Port 2 with the 3300 as
DHCP Server for both networks.
SOLUTION
You may follow the steps below:
1. Enter WUI, click "Advanced - LAN V...
Click on the required link below for full details:
1. VPN DIAL-IN FUNCTION
[HTTP://WWW.DRAYTEK.COM/USER/SUPPORTAPPNOTESDETAIL.PHP?ID=57] (PDF
format)
Describes setting up a LAN to LAN VPN tunnel between a Vigor3300V and
a Vigor2900 router. The Vigor33...
QUESTION:
How do I set up the router to read the incoming website requests'
target domain name, and route the user to the appropriate port on the
co-located server?
ANSWER
When a external user accesses the server by domain name:
1. The user requests...
3 VPNS connection to 3300 but 3rd connection fails with mismatch
preshared key message.
Remote VPN dialing into 3300
DRAYTEK SOLUTION We saw vigor3300 has 3 VPN which remote Gateway is
0.0.0.0. It's incorrect settings.Because when VPN coming in w...
1.)
2.)
3.)
4.)
5.)
6.)
They have the following differences:
* Vigor3300V+ support ISDN,Vigor3300V don't support ISDN.
* The memory of Vigor3300V+ is 128M, the momery of Vigor3300V is
64M,
* The CPU of Vigor3300V+ and Vigor3300V are the same.
The 3300V router does not have a reset button to restore the router
to factory defaults when the login password is not known.
The following steps show how to restore the Vigor3300V to "factory
default" settings.
STEP1:
Obtain the Physical Addr...
This guide will show you the configuration required to establish an IP
Sec VPN tunnel (Main Mode) between a Vigor3300V and a Vigor3900
router.
VIGOR3900 CONFIGURATION
STEP 1:
Go to VPN AND REMOTE ACCESS >> VPN PROFILES configuration menu.
Select IP...
This application note shows you how to configure the Optus supplied
Netgear modem into bridge mode to interface Draytek broadband routers
to Optus cable service.
APPLICABLE DRAYTEK ROUTERS
DrayOS Routers
Vigor2860, Vigor2925, Vigor2760, Vigor283...
Help Desk Software by Kayako